Rank Networks: Google Business Profile management and local link building
    Step-by-step guide

    Set the grid for a map scan

    Choose the grid size, spacing and shape, draw your own area, skip dots on water and in parks, and move or remove dots before a map scan runs.

    Read about Grid Ranker

    Rankings video · 3 of 5Read every tab of your map rank report3:40

    What you need

    • A new scan open in Grid Ranker, or Grid Tracking inside a business, with the business picked.
    • An idea of where your customers come from: a few streets, a town, or a whole county.
    • Nothing is charged while you set the grid. Grid Credits are used only when you press Run scan.
    Step by step
    1. 1

      Pick the size and the spacing

      In the New geo-grid scan panel, choose the Grid size, from 3 by 3 up to 13 by 13, and the Spacing between dots. The label next to Grid size counts the dots, and the line under the boxes says how far the grid reaches from the business, for example 7×7 grid at 0.5 mi spacing (covers a 1.5 mi radius). Switch Distance unit between km and Miles.

      A 7 by 7 grid half a mile apart over Perth. The panel counts 49 dots and says the grid reaches 1.5 miles from the business.
    2. 2

      Size it by distance instead

      If you think in distance rather than spacing, turn on Set by coverage radius and pick the Radius. The spacing is worked out for you. A tight grid shows the streets near the shop; a wide one shows how far across town you reach.

    3. 3

      Choose a square or a round grid

      Under Grid shape, Square lays the dots in rows. Round keeps only the dots inside a circle, which matches a service area better and uses fewer Grid Credits for the same reach.

      Round chosen: the same 7 by 7 grid becomes 37 dots in a circle around the business.
    4. 4

      Draw your own area

      Press Draw, then click the map to add corners around the area you serve. Three or more corners make an area. Press Done and the area fills with dots at the spacing you chose. Use Undo or Clear while drawing, and Edit area or Start again after. Only the 225 dots nearest the business are kept, so widen the spacing for a big area.

      An area drawn with five corners and filled with dots half a mile apart. The panel says how many dots are kept.
    5. 5

      Skip dots on water and in large parks

      Leave Skip points on water and in large parks on. The map is checked for lakes, rivers, sea and big parks, and those dots turn into hollow circles. Hollow dots are not scanned and not charged. The check can take up to a minute on a big grid; the panel says Checking the map for water and parks until it is done.

      Ten dots on the Swan River and in Kings Park are hollow, so the scan uses 39 Grid Credits instead of 49.
    6. 6

      Move, remove or add dots

      Under Edit the grid, click a dot to switch it off and click it again to bring it back. Drag a dot to move it. Press Add points, then click the map to add a dot where customers come from, and press it again to stop. Move grid shifts the whole grid to the next place you click. Recenter puts it back on the business and clears your edits, and Reset edits undoes every change too.

      Two dots switched off (red crosses), one dragged, and two added on the right. The Run scan button counts only the dots that will be scanned.
    7. 7

      Check the cost and run

      The Run scan button shows the dots and the Grid Credits the scan will use: one per dot for each keyword. Press it when the grid looks right. A scheduled scan keeps this exact grid on every run, so the runs can be compared.

    Tips

    • Keep the same size, spacing and shape on every scan of one business. Only runs with the same grid can be compared.
    • For a business that serves a whole region, Round or Draw with wider spacing covers more ground for fewer Grid Credits.
    • A dot that sits on a road out of town tells you little. Switch it off rather than pay for it.
    Questions
    How many dots can a scan have?
    A square grid goes up to 13 by 13, which is 169 dots. A drawn area keeps up to 225 dots, the ones nearest the business.
    Am I charged for hollow dots?
    No. Dots skipped for water or parks, and dots you switch off, are not scanned and not charged. The Run scan button already leaves them out.
    Can I change the grid of a scheduled scan?
    A schedule repeats the grid it was made with, so runs stay comparable. To use a different grid, start a new scan and schedule that one.
    Was this guide helpful?